US models / USD · No active affiliate agreements or commission-earning links.

BLUETTI Elite 300 vs Jackery HomePower 3000 vs Anker F3000

By Fordham Tucker · Updated · US base units

These three store about 3 kWh, but they are not interchangeable. The practical differences are carrying weight, output connections, expansion options and what happens while the unit is plugged into grid power.

This guide covers standalone US units with appliances plugged into their suitable outlets. It does not evaluate installed home systems, transfer equipment, a two-unit 240 V setup or solar production. Specifications and dated offers come from manufacturers; no hands-on tests are claimed.

Compare the complete base unit

US standalone specifications and dated offers, November 16, 2026
SpecificationBLUETTI Elite 300Jackery HomePower 3000Anker SOLIX F3000
Nominal capacity3,014.4 Wh3,072 Wh3,072 Wh
Total continuous AC2,400 W3,600 W3,600 W
Approximate weight57.98 lb59.5 lb91.5 lb
Observed base price$1,199Check current priceCheck current price
ExpansionBase capacity only modeled; verify any expansion claim before budgeting for accessories.Not expandable; do not confuse with other HomePower models.Optional BP3000 packs; base unit only here. Two units plus a hub are a different system.
Bypass / pass-through1,800 W maximum in US bypass mode.Pass-through is supported; exact output ceiling not confirmed in the checked FAQ.High-output bypass depends on the input connection. Confirm the exact circuit, cord and mode; ordinary wall input is not assumed to supply 3,600 W.
Availability checked Nov 16Orderable on manufacturer page; verify delivery at checkoutBase unit orderable; 500 X solar bundle has a separate delayUnit-only listed available; solar-panel bundles may be delayed

BLUETTI Elite 300 technical sourceJackery HomePower 3000 technical sourceAnker SOLIX F3000 technical source

Prices are US observations before tax and optional accessories. The Elite 300 selected base offer showed $1,199, but a separate storefront subtotal displayed $0; we did not verify its final checkout. Jackery and Anker’s exact selected base prices were not captured. A blank price is not zero, and neither receives an automatic budget-filter pass.

A 3 kWh label is not a promise of a full day

Take a combined appliance load averaging 100 W. Assume 90% usable battery, 90% inverter efficiency and 10 W battery-side idle draw. The battery must supply about 121.1 W. Under those assumptions, Elite 300’s 3,014.4 Wh gives about 22.4 hours; either 3,072 Wh unit gives about 22.8 hours.

Size the target, then compare models

24 h × (100 W ÷ 0.90 + 10 W) ÷ 0.90 = 3,230 Wh nominal

With 20% higher appliance demand, the same target needs about 3,822 Wh. These are planning calculations with no recharge, not measured performance or a guaranteed safety margin.

The nominal capacity gap is only about 1.9%. An unmeasured difference in idle draw or conversion losses could matter more than that. We use identical assumptions for a fair arithmetic comparison, not because we know the products perform identically. See how idle draw changes a low-load plan.

A higher inverter rating does not remove socket limits

HomePower 3000 and F3000 list 3,600 W total AC output. Their ordinary 20 A / 120 V sockets are limited to 2,400 W each. You cannot take the entire 3,600 W rating through one such socket. Total demand across outlets must also stay within the unit’s rating. Confirm the appliance’s plug and starting behavior before comparing headline watts.

Elite 300 lists 2,400 W total in US battery mode and 1,800 W in bypass. Its Power Lifting figure describes certain resistive loads; it is not evidence that a refrigerator compressor will start. HomePower 3000’s exact bypass ceiling remains unconfirmed in our checked technical source. F3000’s higher-output pass-through depends on its input arrangement; an ordinary wall connection is not assumed to supply the headline inverter power.

The calculator checks battery-mode energy and total output, with a separate screen for documented standard-socket limits. It does not certify bypass, switching time, temperature behavior or surge duration. Use the pre-purchase checklist and the exact manual when asking the manufacturer about your appliance.

Three questions that separate the choices

Do you need this capacity at all?

If your measured target is closer to 1.5 kWh, the catalog’s Explorer 1500 v2 and Yeti 1500 LFP provide intermediate options worth comparing. If it fits 1 kWh, start with the compact-model comparison. Conversely, if the required energy exceeds 3 kWh, changing to a higher-output inverter does not solve the shortage. Reduce the load, shorten the goal or build a separately verified capacity and recharge plan.

Before ordering, confirm the exact base variant, destination delivery, warranty and return conditions. Some panel bundles have different shipping dates from the station. For cycling refrigerators, check output timeout settings and observe a complete appliance cycle in a supervised trial. Food temperature needs its own monitoring; an hours-remaining display is not that measurement.