Plan a refrigerator and chest freezer on one battery
Add the energy used by each appliance, then check how the pair starts and connects. Enough battery capacity does not establish that the station can run both appliances.
Measure each appliance separately
A kitchen refrigerator and a chest freezer are different loads. Do not copy the refrigerator’s energy estimate into the freezer row or substitute the property’s whole electricity bill. If a label covers a single refrigerator-freezer appliance, enter it once; the second row is for a separate chest freezer.
For a suitably rated plug-in meter, record the change in cumulative kWh and the actual elapsed hours for each appliance. The P3 P4400 manual documents cumulative energy and powered-time readings and warns against exceeding its ratings. Its ordinary watt display is not documented as a compressor-inrush capture function. Follow both appliance and meter instructions; borrow a suitable meter if that resolves the question before a purchase.
Our practical starting sample is 24–72 hours of normal use, followed by a repeat under different conditions. This is an editorial sampling choice, not a manufacturer guarantee. Note room conditions, door openings, loading, settings, resets and interruptions. A garage sample is not automatically representative of a hot summer outage. A short or zero sample may miss operation; investigate it rather than treating the appliance as a free load.
If you only have an annual kWh label, the worksheet converts it to an average using annual kWh × 1,000 ÷ 8,760. The FTC explains how EnergyGuide estimates support appliance comparisons. An annual average is a starting estimate, not a measurement of your kitchen or garage during an outage. Use the kWh figure, not the annual dollar cost.
See the full energy measurement protocol if you need a repeatable record.
Two-appliance energy worksheet
Each appliance can use a different source and sample duration. The starting values below are invented examples. This tool computes energy only and never issues a power-compatibility pass. Entries are processed in this page; they are not uploaded or stored by the tool. Aggregate page analytics do not receive these fields. Privacy details.
Energy estimate only
- Combined average AC load
- —
- Appliance energy for target hours
- —
- Base nominal capacity required
- —
- Higher-demand capacity required
- —
- Base runtime at entered capacity
- —
- Demand-only runtime sensitivity
- —
Power compatibility remains unresolved. Do not buy from this energy estimate alone. Maximum running demand, startup duration, outlet limits and the proposed connections still need evidence.
A 24-hour example, with both readings visible
These invented readings illustrate the arithmetic; they are not typical-use claims or physical tests. The refrigerator sample is 1.80 kWh over 30 hours. The separate chest freezer sample is 1.44 kWh over 48 hours. Different sample lengths are fine: normalize each one before adding them.
| Appliance | Sample | Average AC load | Energy for 24 hours |
|---|---|---|---|
| Refrigerator | 1.80 kWh / 30 h | 60 W | 1.44 kWh |
| Chest freezer | 1.44 kWh / 48 h | 30 W | 0.72 kWh |
| Combined | Normalize, then add | 90 W | 2.16 kWh |
The sample energy totals cannot simply be added and called a “day”: they cover 30 and 48 hours. Dividing each reading by its own elapsed time avoids that mistake.
- Convert the 2.16 kWh of AC appliance energy through an assumed 90% efficiency:
2.16 ÷ 0.90 = 2.40 kWhfrom the battery for the load. - Add assumed battery-side overhead:
10 W × 24 h = 0.24 kWh. Total usable battery energy needed is2.40 + 0.24 = 2.64 kWh. - Keep only 90% of nominal capacity available:
2.64 ÷ 0.90 = 2.93 kWh nominal. Usable share is a divisor; adding a flat 10% is a different calculation.
| Target | Base nominal capacity | With 20% more appliance demand |
|---|---|---|
| 12 hours | 1.47 kWh | 1.73 kWh |
| 24 hours | 2.93 kWh | 3.47 kWh |
| 48 hours | 5.87 kWh | 6.93 kWh |
A hypothetical 2,000 Wh battery gives 16.4 hours in the base case and 13.8 hours with 20% more appliance demand. A 3,000 Wh battery gives 24.5 hours base but only 20.8 hours in the higher-demand case. Passing the base energy target leaves little reason to ignore a less favorable case. Neither calculation verifies startup.
For an example using labels instead, 500 kWh/year for the refrigerator plus 250 kWh/year for the freezer averages 750,000 ÷ 8,760 = 85.6 W. Do not round each appliance to a whole “running wattage” and multiply it by 24; the annual figure already includes its estimated cycling.
Keep losses, reserve and changing conditions separate
Average AC watts = fridge watts + freezer watts + other average AC watts
Battery draw = average AC watts ÷ efficiency + battery-side idle watts
Required nominal Wh = target hours × battery draw ÷ usable share
Runtime hours = nominal Wh × usable share ÷ battery drawThe worked example treats efficiency as conversion loss and idle draw as separate battery-side overhead. If your measured all-in efficiency already includes idle loss, do not add that loss again. The usable-share input is the portion of nominal capacity actually available for this plan after starting charge and the reserve you intend to retain; 90% assumes a fully charged battery with 10% left unused. A partly charged, aged or cold battery needs a justified adjustment.
The ±20% default changes average appliance demand only. It is not a statistical confidence interval and does not model temperature, battery degradation or inverter behavior. Compare repeated samples, and choose a less favorable scenario when the evidence warrants it. Read why idle draw matters at low loads.
The calculation assumes both appliances remain connected for the entire target period and the AC output stays on. It does not recommend alternating their power, warming stored food for a test or relying on a timed duty cycle. No solar, generator or other recharge is credited. For a longer outage, verify a practical recharge plan separately instead of treating panel nameplate watts as guaranteed energy.
Check overlapping starts separately from energy
The example’s 90 W average cannot size the inverter. Record each exact appliance’s maximum running demand and startup demand with its required duration and source. Include every operating mode identified by the appliance maker. An ordinary energy meter display, a generic multiplier or another owner’s refrigerator does not settle this for your equipment.
| Record | Refrigerator | Chest freezer |
|---|---|---|
| Exact model and electrical manual | Record model / source | Record model / source |
| Maximum running watts | R-fridge: unknown | R-freezer: unknown |
| Starting demand and duration | S-fridge: unknown | S-freezer: unknown |
| Supply, outlet and connection restrictions | Not checked | Not checked |
Consider four cases: both running; refrigerator starting while the freezer runs; freezer starting while the refrigerator runs; and overlapping starts. Add the other devices’ simultaneous maximum demand to each. Turning appliances on at different times does not establish that later automatic starts can never overlap.
| Case | Illustrative calculation |
|---|---|
| Both running | 180 W + 120 W = 300 W |
| Fridge starting; freezer running | 1,100 W + 120 W = 1,220 W |
| Freezer starting; fridge running | 800 W + 180 W = 980 W |
| Both starting | 1,100 W + 800 W = 1,900 W |
These sums are conservative planning cases, not a reproduction of motor waveforms. Even a station advertising a larger surge number is not automatically approved: duration, voltage behavior, outlet/group limits and the exact appliances matter. Two sockets do not automatically mean two independent circuits. Use the startup and outlet checklist and confirm the proposed arrangement with the relevant manufacturers.
A shared battery is not permission to share a circuit
GE’s freezer guidance specifies an individual grounded branch circuit and recommends a dedicated circuit for its upright and chest freezers. That is a reason to check the exact freezer’s instructions, not a universal claim about every brand. If the requirement or its application to portable backup is unclear, resolve it before buying or connecting the pair. This guide does not approve splitters, extension arrangements or building-wiring connections.
Check what happens while both compressors are idle and after charging or a shutdown. The EcoFlow DELTA 3 Plus manual, page 13, for example, warns that an intermittent refrigerator load can trigger AC timeout and gives model-specific settings. It is a different model from the DELTA Pro 3 in our comparison. Follow the exact station’s current manual and verify behavior; this example is not a universal setting or uptime guarantee.
Choose the next action before choosing a model
- One energy reading is missing: keep the result unresolved. Measure or find the correct label first. Do not buy a larger battery to cover an unknown input.
- The energy target is met but power or connections are unknown: ask the appliance and station makers about the exact pair and arrangement. More Wh does not resolve an output restriction.
- Only the base scenario fits: review repeated readings, starting charge, reserve and a less favorable demand case before deciding.
- The pair needs more energy than you can practically store or recharge: reconsider the backup plan. Existing compatible equipment, suitable borrowed or rented equipment, or a verified alternative arrangement may be more useful than an oversized purchase. Availability and compatibility are not assumed.
Powered runtime does not establish food temperature or food safety. Use FoodSafety.gov’s separate refrigerator and freezer outage guidance for those decisions. We have not tested this setup, and the worksheet cannot promise food preservation.
Bring evidence to the comparison
Download the energy worksheet, fill the separate power and connection questions, then compare nominal capacity, continuous output, weight and current offer details. An energy estimate alone is not a purchase recommendation.
Browse power-station specificationsFor one appliance instead, use the single-fridge runtime tool or refrigerator runtime examples.
Sources and limits
Official sources checked November 16, 2026. Calculations, worksheet design, sampling suggestions and sensitivity choices are PowerPick’s editorial work. All numerical examples are invented; no physical appliance or battery test is claimed.
P3 International — P4400 cumulative kWh, elapsed time and meter-rating warningFTC — how to use EnergyGuide estimatesGE Appliances — freezer electrical requirements and model-specific instructionsEcoFlow — DELTA 3 Plus US manual, AC timeout guidance (PDF page 13)FoodSafety.gov — outage food-temperature decisionsManufacturer guidance is model-specific. Generic starting multipliers are not treated as measured inrush. Read our full comparison method.