Power station idle draw: why low loads get less runtime
A 10 W appliance does not necessarily take only 10 W from a battery. Keeping the AC inverter awake uses energy too. That fixed overhead matters most when the device you are powering uses very little.
What to check before buying
For a router, small light or another low AC load, compare idle consumption and low-load shutdown behavior as well as battery capacity. A larger watt-hour number alone does not tell you how long the setup will stay on.
The examples below are calculations with declared assumptions. They are not measurements of the Jackery, BLUETTI or EcoFlow models in our shortlist.
Separate the appliance, conversion loss and idle draw
Your AC appliance uses energy at the outlet. The inverter converts the battery's stored energy into AC, with losses. The electronics can also consume energy while the AC output is enabled, even when the appliance uses very little or nothing.
These are separate terms in PowerPick's planning model:
Battery-side draw (W) = average AC load (W) ÷ conversion efficiency + battery-side idle draw (W)Runtime (hours) = nominal capacity (Wh) × usable share ÷ battery-side draw (W)
Here, conversion efficiency excludes the separately entered idle term. If a measured efficiency figure already includes all losses at your load, adding idle consumption again would count part of the loss twice. See the full calculation method before substituting a manufacturer's percentage.
There is no universal idle wattage. Goal Zero describes roughly 10 W for its Yeti 1500. Jackery lists standby consumption of at most 16 W for the HomePower 2000 Plus V2, model JHP-2000A. Those are manufacturer statements about different models and potentially different operating conditions. Neither is an idle-draw measurement for the Explorer 2000 v2, Elite 200 V2 or DELTA Pro 3 shown on our homepage.
What 0, 10 or 20 W of overhead does to runtime
Hold the other assumptions constant: a hypothetical 2,000 Wh battery, 90% usable share, 90% conversion efficiency, a constant average AC load and no recharging. The 0 W column means no fixed overhead is included in that scenario; it does not claim a real inverter has no idle draw.
| Average AC load | 0 W idle | 10 W idle | 20 W idle |
|---|---|---|---|
| 10 W | 162.0 h | 85.3 h | 57.9 h |
| 50 W | 32.4 h | 27.5 h | 23.8 h |
| 100 W | 16.2 h | 14.9 h | 13.7 h |
At a 10 W load, adding the illustrative 10 W idle term changes the result from 162.0 to 85.3 hours. At 100 W, the same change reduces 16.2 to 14.9 hours. This is why a fixed loss deserves more attention for a small load.
These columns are assumption choices, not a measured confidence interval. Actual efficiency, temperature, battery condition and control behavior can put a real setup outside the table. A display reading of 0 W at the AC output also does not establish zero internal battery use.
A 24-hour plan for an illustrative 12 W setup
Suppose a measured collection of low-power devices averages 12 W at the AC outlet. For 24 hours, the devices themselves need 288 Wh. With a 90% conversion assumption and 10 W of battery-side idle draw, the battery supplies 560 Wh: 320 Wh for converted appliance energy plus 240 Wh of idle energy.
If you start full and plan to leave a 10% reserve, nominal capacity needs to be 560 ÷ 0.90 = approximately 622 Wh. This is an energy budget for the example, not a minimum product recommendation or a guarantee that a particular small battery will work.
| Assumed idle | Battery energy used | Nominal capacity with 10% reserve |
|---|---|---|
| 0 W | 320 Wh | 356 Wh |
| 10 W | 560 Wh | 622 Wh |
| 20 W | 800 Wh | 889 Wh |
For a refrigerator plus other loads, first calculate average demand from its annual label or your measurement. Our 12-, 24- and 48-hour refrigerator sizing example covers that separate job. Starting power, individual outlet limits and restart behavior still require the startup checklist.
What a measurement can—and cannot—tell you
- Measure the load you intend to back up. Include the actual adapters and all devices that must remain on. A meter's cumulative kWh divided by elapsed hours gives average AC demand. The P3 P4400 manual distinguishes accumulated kWh from elapsed hours and instantaneous watts; stay within the meter's labeled ratings.
- Identify where the measurement was taken. An AC output meter measures energy delivered to the devices. It does not directly measure battery-side inverter overhead. Do not relabel its reading as internal idle draw.
- Ask for comparable evidence. Look for the exact model, enabled outputs, load, starting charge, cutoff/reserve, firmware and test duration. A broad efficiency percentage or one short display reading leaves those conditions unresolved.
- Preserve unknowns. Until you have model-specific evidence, compare several reasonable planning assumptions instead of presenting one exact runtime. Our measurement worksheet helps record energy and conditions; it is not a laboratory inverter test.
Check low-load shutdown as well as energy
There is another way a small or cycling load can stop: the station may turn its output off after a quiet interval. More stored energy does not solve a disabled outlet. The US DELTA 3 Plus manual includes AC-timeout guidance for intermittently operating appliances. It is an example of a model-specific setting, not an instruction for the different DELTA Pro 3 or every other station.
Use the manual for your exact unit and current firmware, then confirm normal restart and low-load operation in a supervised readiness check. Do not disable protective functions generically. Keep energy duration and output availability as separate buying questions.
When a smaller option—or no purchase—is the better next step
If the whole requirement is a small network load, compare an appropriately specified UPS or manufacturer-supported DC backup before buying a heavy 2 kWh station. Check its actual energy capacity, output and connection requirements, not only its VA or watt rating. A suitable DC path may avoid running an AC inverter, but it still has losses and must match the equipment's voltage, polarity, connector and current requirements. Do not improvise adapters.
Powering a modem, router or fiber terminal at home does not ensure the provider's network remains available. List every device required by your connection and verify the provider's backup limitations. If your load estimate is uncertain, borrowing a suitable meter and gathering better evidence may be the useful first step.
A higher capacity station can still be appropriate for a refrigerator or several devices. Make that decision after measuring demand and checking output compatibility—not because a large inverter is automatically efficient at a tiny load.
Use the assumption that fits your evidence
In the runtime calculator, open “Energy assumptions & separate power check” to change idle draw and efficiency. The default 10 W is illustrative. It is not a test result for the three listed products.
Estimate with your loadSources and limits
Official references reviewed November 15, 2026. The equations and tables are PowerPick calculations; no product was physically tested for this guide.
- Goal Zero: Yeti 1500 FAQ — model-specific idle explanation and approximately 10 W manufacturer statement.
- Jackery: HomePower 2000 Plus V2 basic information — JHP-2000A standby limit; not the Explorer 2000 v2.
- P3 P4400 operation manual — cumulative energy, elapsed time and rating limits.
- EcoFlow DELTA 3 Plus US manual — model-specific AC timeout behavior; not DELTA Pro 3.