US models / USD · No active affiliate agreements or commission-earning links.

C1000 Gen 2 vs HomePower 1000 Plus v2 vs OUPES Mega 1

By Fordham Tucker · Updated · US base units

All three store a nominal 1,024 Wh. Start with how much energy you need, then decide whether carrying weight, battery expansion or the electrical limits justify the purchase.

This is a comparison of manufacturer specifications and dated US offers. We have not tested runtime, noise, reliability or customer service. A larger inverter number does not establish longer refrigerator runtime.

Three base units, three different expansion decisions

US standalone specifications and dated offers, November 16, 2026
SpecificationAnker SOLIX C1000 Gen 2Jackery HomePower 1000 Plus v2 · WhiteOUPES Mega 1
Nominal capacity1,024 Wh1,024 Wh1,024 Wh
Total continuous AC2,000 W1,800 W2,000 W
Approximate weight24.9 lb23.8 lb27.8 lb
Observed base priceCheck current price$779$699
ExpansionNo battery expansion; do not confuse with original C1000.Only Battery Pack 2000 Plus v2; not the older 2000 Plus or 1000 Plus packs.Up to 5,120 Wh total with two optional B2 packs; base listing is 1,024 Wh.
Bypass / pass-through1,800 W maximum in bypass; lower than battery output.15 A maximum, reduced to 12 A after 3 hours; confirm the mode for continuous use.2,000 W bypass rating; manual also requires combined input/output below 2,000 W in EPS mode. Verify the exact setup.
Availability checked Nov 16Unit-only listed available; some solar bundles delayedWhite in stock; Black is preorderStandalone Add to cart available

Anker SOLIX C1000 Gen 2 technical sourceJackery HomePower 1000 Plus v2 · White technical sourceOUPES Mega 1 technical source

These are three model families, not three bundles. Adding a solar panel does not change stored battery capacity. An expansion pack does, and must be budgeted, carried and connected separately. The table excludes both. Select the exact generation: original C1000, HomePower 1000 v2 without “Plus,” and Mega 1 Lite are different products.

What 1 kWh might mean for your refrigerator

Suppose your meter records 1.2 kWh over a full 24 hours: that is an average 50 W, including cycling during that sample. Add a router averaging 10 W. With an assumed 90% usable battery, 90% inverter efficiency and 10 W battery-side idle draw, the combined draw is about 76.7 W.

Worked example, not a product test

1,024 Wh × 0.90 ÷ (60 W ÷ 0.90 + 10 W) = 12.0 hours

Each of these units gets the same 12.0-hour estimate because the calculator uses the same capacity and assumptions. With appliance demand 20% higher, the estimate drops to 10.2 hours. That sensitivity is an illustration, not a guaranteed range.

For that same load, a 24-hour target calls for about 2.05 kWh nominal in the base case, or 2.40 kWh with 20% higher demand. None of these base units meets that target in this example. A sale price or 2,000 W inverter cannot fix an energy shortfall. Try your numbers in the runtime calculator; if you also need a chest freezer, use the two-appliance worksheet.

Choose according to the constraint you actually have

Battery output and wall-powered bypass are separate checks

When a station stays plugged into a wall, it may pass grid power through to the appliance. That operating mode can have a lower ceiling than battery operation. C1000 Gen 2 lists a 1,800 W bypass maximum. Jackery’s FAQ applies a lower current limit after three hours. OUPES lists 2,000 W bypass but its EPS instructions also constrain combined input and output. Those details are reasons to read the exact manual, not to treat a large inverter label as universal permission.

Refrigerators also stop drawing compressor power between cycles. Confirm that any low-load timeout leaves the AC outlet available long enough for the next start. Manufacturer standby figures do not establish comparable real-world idle losses; we do not plug them into the calculator as if measured under the same conditions.

A short purchase worksheet

  1. Record appliance energy over representative conditions, plus maximum running demand and evidence about starting demand.
  2. Choose the exact US generation, color and base-unit contents. Compare delivered cost, return shipping and the current return conditions.
  3. Confirm individual outlet limits, bypass behavior, required surge duration and timeout settings with the manufacturer.
  4. Plan a supervised trial with your actual appliances while you can still return the purchase under its terms. Keep refrigerator temperature monitoring separate from the battery display.

If your result fits a smaller existing or borrowed battery, investigate that before buying. If 1 kWh is clearly too small, compare three roughly 3 kWh options or the intermediate 1.5 kWh units in the full catalog.